August 2015 - ROM GURUS

Looking for firmware, Stock ROM or how to go about that phone problem? You are in the right place, get all you want here for free...

Thursday

Download All Gionee Stock ROM

5:56 am 4
Download All Gionee Stock ROM

How to Create Stock ROM Using MTK Droid Tools

3:12 am 10
How to Create Stock ROM Using MTK Droid Tools
This Method will tech you how to create stock ROM using MTK droid tools, it is the same for all MTK Android Devices.

Tools Require

* A working Android phone
* Download PdaNet

* Download MTKDroid Tools
* PC
* USB Cord
* Enough space  (at least 4GB) on the SD card / phone Storage (to avoid the insufficient storage space error)

Please Note

* If you get an error saying "Error: file adb not install" click here to fix it
* If you get an error saying "insufficient space on device" then ensure there's at least 4GB free space on both phone storage and SD card (if supported) then install Busybox on the phone
* If you get an error like "Preparation of files for FlashTool is impossible, file isn't found" then remove all scatter files in the backup folder except one and rename this last one to MT65??_Android_scatter ( where "??" represents the number for your phone model e.g MT6572_Android_scatter)
* If you get an error like "ERROR: Zero file, no space left on device!" click here
* If you get -- ERROR : --- TotalBytesPerChunk Not Found. Set default Page/Spare=2048/64 !!! then slot in an SD card into the phone and install Busybox on the phone.

Procedure

* Enable USB debugging on the good MTK phone (Settings > Developer > Tick USB Debugging) then connect it to PC. If you don't find Developer under Settings then go to Settings > About > Keep taping Build Number
* Install PdaNet on the PC with the USB debugging enabled working MTK phone still connected (Select Other from the list of devices during installation)
* At the end of PdaNet installation, you should get a "drivers successfully installed" message
* Exit PdaNet in system tray (bottom right corner of PC)
* Launch MTK droid tools as Administrator (right-click > run as Administrator) still with the working MTK phone connected to PC
* MTK droid tools should detect and display the phones details by the left along with a yellow box at the bottom
* Click ROOT at the bottom of MTK and select Yes/OK if prompted on PC and Grant if prompted on phone
* A progress bar should load at the bottom shortly after which the yellow box should become green
* Click on the root,backup,recovery tab at the top
* Click Backup (MTK should keep writing some things by the right hand side during backup) and wait till backup is complete
* If you get a prompt to pack backup, select No.
* Once backup is complete, don't close MTK droid tools
* Go to the MTK droid tools folder > Backups > Folder named after the phone's model e.g Tecno_m3_backup.... and take note of this folder as the 'Backup folder' because we'll be referring to it soon
* Go back to MTK droid tools and click 'To prepare blocks for Flash Tool'
* A window will open, in this window, navigate to the Backup folder (mentioned above) and select the md5 file
* MTK will start copying some items (check the right hand side) so wait till copying is complete
* Once copying is complete, open the Backup folder and you should see a folder named "!Files to flash"
* The !files to flash folder is a selection of files needed to use Sp Flash tool, keep it well
* Both the !files to flash folder and the x_backup folder (which contains the !files to flash folder) are your phone's MTK backup

* If you need an MTK Droid tools backup of usrdata and cache then use MTK Droid Tools version 2.3.0 or do a read back using Sp flash tool click here
This procedure is the same for all MTK based Android phones (e.g Tecno, Gionee, Infinix, TLC, Opsson, Innjoo, Lead1 etc )

# See the video tutorial below or @ http://youtu.be/AJLgSD9zHb8





Tools needed

* A working MTK phone
* Download PdaNet
* Download MTK Droid tools
* PC
* USB Cord
* Enough space  (at least 4GB) on the SD card / phone Storare (to avoid the insufficient strorage space error)

Note

* If you get an error saying "Error: file adbd not install" then read https://forum.hovatek.com/thread-1219.html to fix it
* If you get an error saying "insufficient space on device" then ensure there's at least 4GB free space on both phone storage and SD card (if supported) then install Busybox on the phone
* If you get an error like "Preparation of files for FlashTool is impossible, file isn't found" then remove all scatter files in the backup folder except one and rename this last one to MT65??_Android_scatter ( where "??" represents the number for your phone model e.g MT6572_Android_scatter)
* If you get an error like "ERROR: Zero file, no space left on device!" then read https://forum.hovatek.com/thread-6407.html
* If you get -- ERROR : --- TotalBytesPerChunk Not Found. Set default Page/Spare=2048/64 !!! then slot in an SD card into the phone and install Busybox on the phone.

Procedure

* Enable USB debugging on the good MTK phone (Settings > Developer > Tick USB Debugging) then connect it to PC. If you don't find Developer under Settings then go to Settings > About > Keep taping Build Number
* Install PdaNet on the PC with the USB debugging enabled working MTK phone still connected (Select Other from the list of devices during installation)
* At the end of PdaNet installation, you should get a "drivers successfully installed" message
* Exit PdaNet in system tray (bottom right corner of PC)
* Launch MTK droid tools as Administrator (right-click > run as Administrator) still with the working MTK phone connected to PC
* MTK droid tools should detect and display the phones details by the left along with a yellow box at the bottom
* Click ROOT at the bottom of MTK and select Yes/OK if prompted on PC and Grant if prompted on phone
* A progress bar should load at the bottom shortly after which the yellow box should become green
* Click on the root,backup,recovery tab at the top
* Click Backup (MTK should keep writing some things by the right hand side during backup) and wait till backup is complete
* If you get a prompt to pack backup, select No.
* Once backup is complete, don't close MTK droid tools
* Go to the MTK droid tools folder > Backups > Folder named after the phone's model e.g Tecno_m3_backup.... and take note of this folder as the 'Backup folder' because we'll be referring to it soon
* Go back to MTK droid tools and click 'To prepare blocks for Flash Tool'
* A window will open, in this window, navigate to the Backup folder (mentioned above) and select the md5 file
* MTK will start copying some items (check the right hand side) so wait till copying is complete
* Once copying is complete, open the Backup folder and you should see a folder named "!Files to flash"
* The !files to flash folder is a selection of files needed to use Sp Flash tool, keep it well
* Both the !files to flash folder and the x_backup folder (which contains the !files to flash folder) are your phone's MTK backup
* If you need an MTK Droid tools backup of usrdata and cache then use MTK Droid Tools version 2.3.0 or do a read back using Sp flash tool (see https://forum.hovatek.com/thread-526.html ) - See more at: https://forum.hovatek.com/thread-468.html#sthash.S6wsocNU.dpuf

How To Unbrick Android Phone Using SP-Flash Tools

3:10 am 1
How To Unbrick Android Phone Using SP-Flash Tools
Have you damage your handheld device software? Do you want to fix it and don`t know how? This simple and effective method will teach you how to unbrick android phones using Sp-flash tools
 
Requirement

* A PC
* USB Cord
* Click here to download and Manually install VCOM drivers on your PC
* Ensure there's an SD card in the phone you wish to flash the files to
* Scatter file + files to be flashed Click here to see how to make an MTK Backup).
* Download SP Flash tool ( Version 5.x  )

Note
If you get any error in SP Flash tool or the phone still didn't work after flashing, I made a list of SP Flash Tool errors, their meanings and how to resolve them click here to see.

Procedure
  • Remove the battery from the phone and slot it back in without booting the phone (If the battery is inbuilt then simply switch if off). Also, ensure there's a formatted SD card in the phone (if there's an SD card slot)
  • Launch SP Flash Tool as Administrator

How-To-Unbrick-Android-Phone-Using-SP-Flash-Tools
  • Click on Scatter-loading by the right
How-To-Unbrick-Android-Phone-Using-SP-Flash-Tools
  •  In the window that pops up, select the scatter file for your phone model then click Open (scatter file is a text file with the word "scatter" in its name
How-To-Unbrick-Android-Phone-Using-SP-Flash-Tools
  •  A list with ticked boxes should appear in SP flash tool (preloader, mbr, ebr etc)
  • Step a,b,c,d,e,f

These steps is only for when you wish to format the phone. Skip if you don't wish to format

  • a. Click Format at the top
  • b. After clicking Format, a dialogue box will pop up, ensure that 'Auto Format Flash' and 'Format whole flash without Boot-loader' are selected
  • c. Click OK, Stop should now be red or green in color
  • d. Connect the switched off phone (with battery inside) to the PC via USB cord
  • e. A progress bar should load till you get a 'Success' message (green circle with OK)
  • f. Disconnect the phone from PC
  • . Uncheck the box in front of any item you do not wish to flash
How-To-Unbrick-Android-Phone-Using-SP-Flash-Tools
  • To manually load an item that doesn't automatically get ticked after loading the scatter file, tick the box in front of that item then double-click its Location and select the corresponding file in the window that pops up
  • Once the file(s) you wish to flash is (are) ticked, click Download (with an arrow above it)
How-To-Unbrick-Android-Phone-Using-SP-Flash-Tools
  • Stop should now be prominent while other options should be grayed out
  • Connect the switched off phone (with battery inside) to the PC via USB cord
  • A progress bar should start running.
How-To-Unbrick-Android-Phone-Using-SP-Flash-Tools
  • Wait till you get a Success message (green circle with OK), do not interrupt before then
  •  Disconnect the phone, remove the battery for 15 seconds (if removable), slot it back in then power up the phone
  • Ensure to do a factory reset in recovery mode to clear any errors

How To Install MT65xx MediaTek USB VCOM Drivers on Window Manually

2:37 am 2
How To Install MT65xx MediaTek USB VCOM Drivers on Window Manually

This tutorial will teach you how to install MT65xx mediatek USB VCOM drives on any windows operating system manually. It is a straight and painless procedure, so sit back and enjoy.

Requirement


Note:  

  1. You might need to disable drivers signature verification in Windows for this to work smoothly. 
  2. If you have access to a working phone of the same model then remove the battery from the working phone and connect to PC via USB cord. Mediatek preloader VCOM drivers should be automatically installed so you can skip the rest of this guide

Procedure
  • Install USB Deview and use it to uninstall all Vcom, Mediatek and Preloader drivers
  • Extract the contents of the Mediatek USB VCOM file above (input Hovatek if it file request for a password when extracting)
  • In Windows, go to Control Panel and open Device Manager
  • Click any of the device groups (any of the items on the list) you see there, then from Action menu, select Add legacy hardware
  • Add hardware wizard will be opened, click next
  • Select Install the hardware that I manually select from a list (Advanced)
  • Click next two times and click Have Disk button
  • Click browse and find where your driver's .inf file is, then select it (the .inf you'll select is located in drivers > USB Vcom driver > your OS) . Ensure to select the 64 bit .inf if your PC is 64 bit
  •   Click Open and OK. You will see the drivers listed.
  • Select your driver there (select Mediatek Preloader USB VCOM Port)
  • Click Next and finish installing
  • If SP flash tool or other software still dont detect your phone then also install Mediatek DA VCOM (consider installing more from the list of drivers one at a time if need be  )
  • If you get the code 10 error after the installation, simply ignore it and proceed with SP flash tool. You're only getting that error because the driver is not digitally signed.

How to manually install MT65xx (MediaTek) USB VCOM drivers on Windows - See more at: https://forum.hovatek.com/thread-440.html#sthash.5Md8TUUb.dpuf
Requirement

1. Download MediaTek USB VCOM drivers
2. Download USB Deview ( 32 bit here : 64 bit here )

Note: 
* You might need to disable drivers signature verification in Windows for this to work smoothly.  see  http://forum.hovatek.com/thread-752.html for the procedure

* If you have access to a working phone of the same model then remove the battery from the working phone and connect to PC via USB cord. Mediatek preloader VCOM drivers should be automatically installed so you can skip the rest of this guide

Procedure

# See the video tutorial below or @ http://youtu.be/sADkzyI8Z5Q





1. Install USBDeview and use it to uninstall all Vcom, Mediatek and Preloader drivers
1b. Extract the contents of the Mediatek USB VCOM file above ( The Password when extracting is Hovatek )
2. In Windows, go to Control Panel and open Device Manager
3. Click any of the device groups (any of the items on the list) you see there, then from Action menu, select Add legacy hardware
4. Add hardware wizard will be opened, click next
5. Select Install the hardware that I manually select from a list (Advanced)
6. Click next two times and click Have Disk button
7. Click browse and find where your driver's .inf file is, then select it (the .inf you'll select is located in drivers > USB Vcom driver > your OS) . Ensure to select the 64 bit .inf if your PC is 64 bit
8. Click Open and OK. You will see the drivers listed.
9. Select your driver there (select Mediatek Preloader USB VCOM Port)
10. Click Next and finish installing
11. If SP flash tool or other software still dont detect your phone then also install Mediatek DA VCOM (consider installing more from the list of drivers one at a time if need be  )
12. If you get the code 10 error after the installation, simply ignore it and proceed with SP flash tool. You're only getting that error because the driver is not digitally signed.
- See more at: https://forum.hovatek.com/thread-440.html#sthash.5Md8TUUb.dpuf
Requirement

1. Download MediaTek USB VCOM drivers
2. Download USB Deview ( 32 bit here : 64 bit here )

Note: 
* You might need to disable drivers signature verification in Windows for this to work smoothly.  see  http://forum.hovatek.com/thread-752.html for the procedure

* If you have access to a working phone of the same model then remove the battery from the working phone and connect to PC via USB cord. Mediatek preloader VCOM drivers should be automatically installed so you can skip the rest of this guide

Procedure

# See the video tutorial below or @ http://youtu.be/sADkzyI8Z5Q





1. Install USBDeview and use it to uninstall all Vcom, Mediatek and Preloader drivers
1b. Extract the contents of the Mediatek USB VCOM file above ( The Password when extracting is Hovatek )
2. In Windows, go to Control Panel and open Device Manager
3. Click any of the device groups (any of the items on the list) you see there, then from Action menu, select Add legacy hardware
4. Add hardware wizard will be opened, click next
5. Select Install the hardware that I manually select from a list (Advanced)
6. Click next two times and click Have Disk button
7. Click browse and find where your driver's .inf file is, then select it (the .inf you'll select is located in drivers > USB Vcom driver > your OS) . Ensure to select the 64 bit .inf if your PC is 64 bit
8. Click Open and OK. You will see the drivers listed.
9. Select your driver there (select Mediatek Preloader USB VCOM Port)
10. Click Next and finish installing
11. If SP flash tool or other software still dont detect your phone then also install Mediatek DA VCOM (consider installing more from the list of drivers one at a time if need be  )
12. If you get the code 10 error after the installation, simply ignore it and proceed with SP flash tool. You're only getting that error because the driver is not digitally signed.
- See more at: https://forum.hovatek.com/thread-440.html#sthash.5Md8TUUb.dpuf
Requirement

1. Download MediaTek USB VCOM drivers
2. Download USB Deview ( 32 bit here : 64 bit here )

Note: 
* You might need to disable drivers signature verification in Windows for this to work smoothly.  see  http://forum.hovatek.com/thread-752.html for the procedure

* If you have access to a working phone of the same model then remove the battery from the working phone and connect to PC via USB cord. Mediatek preloader VCOM drivers should be automatically installed so you can skip the rest of this guide

Procedure

# See the video tutorial below or @ http://youtu.be/sADkzyI8Z5Q





1. Install USBDeview and use it to uninstall all Vcom, Mediatek and Preloader drivers
1b. Extract the contents of the Mediatek USB VCOM file above ( The Password when extracting is Hovatek )
2. In Windows, go to Control Panel and open Device Manager
3. Click any of the device groups (any of the items on the list) you see there, then from Action menu, select Add legacy hardware
4. Add hardware wizard will be opened, click next
5. Select Install the hardware that I manually select from a list (Advanced)
6. Click next two times and click Have Disk button
7. Click browse and find where your driver's .inf file is, then select it (the .inf you'll select is located in drivers > USB Vcom driver > your OS) . Ensure to select the 64 bit .inf if your PC is 64 bit
8. Click Open and OK. You will see the drivers listed.
9. Select your driver there (select Mediatek Preloader USB VCOM Port)
10. Click Next and finish installing
11. If SP flash tool or other software still dont detect your phone then also install Mediatek DA VCOM (consider installing more from the list of drivers one at a time if need be  )
12. If you get the code 10 error after the installation, simply ignore it and proceed with SP flash tool. You're only getting that error because the driver is not digitally signed.
- See more at: https://forum.hovatek.com/thread-440.html#sthash.5Md8TUUb.dpuf
Requirement

1. Download MediaTek USB VCOM drivers
2. Download USB Deview ( 32 bit here : 64 bit here )

Note: 
* You might need to disable drivers signature verification in Windows for this to work smoothly.  see  http://forum.hovatek.com/thread-752.html for the procedure

* If you have access to a working phone of the same model then remove the battery from the working phone and connect to PC via USB cord. Mediatek preloader VCOM drivers should be automatically installed so you can skip the rest of this guide

Procedure

# See the video tutorial below or @ http://youtu.be/sADkzyI8Z5Q





1. Install USBDeview and use it to uninstall all Vcom, Mediatek and Preloader drivers
1b. Extract the contents of the Mediatek USB VCOM file above ( The Password when extracting is Hovatek )
2. In Windows, go to Control Panel and open Device Manager
3. Click any of the device groups (any of the items on the list) you see there, then from Action menu, select Add legacy hardware
4. Add hardware wizard will be opened, click next
5. Select Install the hardware that I manually select from a list (Advanced)
6. Click next two times and click Have Disk button
7. Click browse and find where your driver's .inf file is, then select it (the .inf you'll select is located in drivers > USB Vcom driver > your OS) . Ensure to select the 64 bit .inf if your PC is 64 bit
8. Click Open and OK. You will see the drivers listed.
9. Select your driver there (select Mediatek Preloader USB VCOM Port)
10. Click Next and finish installing
11. If SP flash tool or other software still dont detect your phone then also install Mediatek DA VCOM (consider installing more from the list of drivers one at a time if need be  )
12. If you get the code 10 error after the installation, simply ignore it and proceed with SP flash tool. You're only getting that error because the driver is not digitally signed.
- See more at: https://forum.hovatek.com/thread-440.html#sthash.5Md8TUUb.dpuf

Wednesday

Download All HTC RUU Stock ROM Files

6:32 am 8
Download All HTC RUU Stock ROM Files
Download-All-HTC-RUU-Stock-ROM-Files
Download All HTC RUU Stock ROM Files

To learn how to flash, unbrick and upgrade HTC devices using any of the RUU files below, please click here for detailed illustration and procedures.
Select and Download any of your required HTC Stock ROM/RUU Files.
Arranged in no particular order...


  1. HTC Desire
  2. HTC Holiday
  3. HTC Butterfly
  4. HTC Incredible
  5. HTC One
  6. HTC One M8
  7. HTC One Max
  8. HTC One V
  9. HTC One VX
  10. HTC Pyramid (Sensation)
  11. HTC Ace
  12. HTC Liberty
  13. HTC Shooter
  14. HTC Legend
  15. HTC Epic Touch 4G
  16. HTC Endeavor
  17. HTC Hero
  18. HTC Dragon
  19. HTC Click
  20. HTC Doubleshot
  21. HTC Bravo
  22. HTC Bravo C
  23. HTC Buzz
  24.  HTC Chacha
  25. HTC Evita
  26. HTC Flyer
  27. HTC Saga
  28. HTC Jewel
  29. HTC Pico
  30. HTC Sapphire
  31. HTC Speedy
  32. HTC Vision
  33. HTC Vigor
  34. HTC Vivo
  35. HTC Vivo W
  36. HTC Ville
  37. HTC Mavel
  38. HTC Runnymede
  39. HTC Kingdom
  40. HTC Mecha
  41. HTC Huangshan
  42. HTC Lexikon



To download and learn how use SP Flash Tools to unbrick your phone, click here 
To download and learn how to create scatter file and ROM Back using MTK Droid Tools click here

How To Flash Unbrick And Upgrade HTC Devices Using RUU Files

6:12 am 0
How To Flash Unbrick And Upgrade HTC Devices Using RUU Files
How-to-flash-unbrick-and-upgrade-htc-devices-using-ruu-files
This tutorial will guide you on how to how to flash or unbrick or upgrade HTC devices using RUU Files
If you`ve messed up your HTC device either by rooting, installing some custom ROM etc or you just want to get back to the default stock ROM, follow the simple guide below.

Note: A wrong RUU will not install on your device. So no harm.


If you want to install RUU files of different variant of your device you will need to be on super CID.
Watch video tutorial from here


Download an install android USB drivers from here
Boot up your phone by pressing volume down and power button
Check the model of the device you want to flash example Pyramid.
Check the radio version (This is very important).

How-to-flash-unbrick-and-upgrade-htc-devices-using-ruu-files
Use power button to select fast-boot on your device.
Download the RUU file of your device. Make sure the file you are downloading has the same radio version with the one of your device. Get RUU files from here
Launch the RUU file.
When it loads, tick I understand the caution...... and select NEXT
Now connect your phone to the computer using a USB cable.
Tick the box and select NEXT
A new pop up will appear Click UPDATE.
How-to-flash-unbrick-and-upgrade-htc-devices-using-ruu-files
  • Verify the images of the ROM you want to flash and click NEXT.
  • Flashing Process will begin.
  • This process can take about 10mins.
How-to-flash-unbrick-and-upgrade-htc-devices-using-ruu-files
  • Wait for the process to complete.
Please do not disturb the device or it might end up hard bricked. Phone will reboot after the process is completed 100%.
Initial boot after this process is longer than usual.Be calm and stay patient for initial boot to complete.

Tuesday

How To Flash or Upgrade Samsung Smartphone Devices Using Odin

2:26 am 1
How To Flash or Upgrade Samsung Smartphone Devices Using Odin
This method will show you how to flash, upgrade or unbrick Samsung devices using Odin. Please follow these simple steps below carefully so as to avoid permanent damage on your smart phone.

Download an install Samsung USB Drivers here.
Download Odin (latest version preferred) here.
Download the exact ROM for your device. Check and download Samsung ROM(s) click here

  Click here to watch the Video Illustration
  • Launch Odin
  • Make sure only Auto Reboot & F. Reset Time is ticked.
  •  Put your device into download mode by pressing down Volume Down > Home > Power key
  • Press volume up on the screen that has a yellow triangle to get into Odin mode.


How-To-Flash-or-Upgrade-Samsung-Smartphone-Devices-Using-Odin


  • Connect the device to the computer.
  • Added!! will be seen showing the device has connected successfully.
  • Click on AP (new versions of Odin) or PDA (older versions of Odin).
  • Navigate to the folder containing the ROM of the device.
  • Select the ROM. (ROM(s) names always end with .tar or .md5).
  • Wait for Odin to process the ROM.
  • Click start.
How-To-Flash-or-Upgrade-Samsung-Smartphone-Devices-Using-Odin

The flashing or upgrading process will now begin.
A green progress bar will be seen at the top left.
This process will take about 8mins or more (depends on the size of the ROM.
When you see PASS! at the top of Odin GUI know that you have successfully flashed or upgraded the device

How-To-Flash-or-Upgrade-Samsung-Smartphone-Devices-Using-Odin

The device will reboot.
First boot after this process takes time. Be patient.......................

Do a factory reset if phone boot-loops.
Press Volume up > Home > Power key
Select factory reset.
You will see No No No No No
Scroll down to Yes.
And Reset Your Device




Download All Samsung Galaxy Stock ROM

2:18 am 2
Download All Samsung Galaxy Stock ROM
Download-All-Samsung-Galaxy-Stock-ROM

Download all Samsung Galaxy Stock ROM or firmware.
Click here to download and learn how to Flash/upgrade Samsung Smartphone Devices using Odin
To download and learn how to use SP Flash Tools to un-brick your phone, click here
To download and learn how to create scatter file and ROM Backup using MTK Droid Tools click here
Click here to download All Samsung USB Driver


Galaxy S DUOS GT-S7562
Galaxy S DUOS GT-S7562 (Clone)
Galaxy Grand Prime DUOS SM-G530BT
Galaxy Pocket Neo DUOS GT-S5312B
Galaxy Grand Quattro GT-i8552 ROM
Galaxy Grand Quattro GT-i8552 Stock Recovery
Galaxy Tab 3 10.1 GTP5210
Galaxy Star Trios GT-S5283B
Galaxy Win DUOS GT-I8552B
========Galaxy S4 ROM=========
Galaxy SHG I337 & I337M AT&T All Firmware
Galaxy GT I9505 OS 5.0.1
  Galaxy GT I9505 OS 4.4.2
 Galaxy GT I9500 O.S 5.0.1
Galaxy GT I9500 O.S 4.4.2
Galaxy GT I9500 O.S 4.4.2 Black Edition
Galaxy GT I9500 O.S 4.3
Galaxy GT I9500 O.S 4.2.2
 Galaxy GT I9502 O.S 5.0.1
Galaxy LTE SHV E300S SKUAMDK
Galaxy LTE SHV E300S SKSUEMJA
Galaxy LTE SHV E300S SKUFNB2
==============================
Galaxy S3 i9300
Galaxy Star Pro GT 7262
Galaxy Grand Prime DUOS SM-G530BT
Galaxy Pocket Neo DUOS GT-S5312B
Galaxy Star Trios GT-S5283B
Galaxy Win DUOS GT-I8552B
Galaxy S3 i9300
Galaxy Pocket 2 DUOS SM-G110B
Galaxy Ace 4 Lite DUOS SM-G313ML
Galaxy Note 3 LTE SM-9005
Galaxy Note 2 N7100
Galaxy Fame DUOS S6812B
Galaxy Young Plus TV S6293T
Galaxy Core Plus SM-G3502T
Galaxy S5 mini SM-G800H
Galaxy Core 2 Duos SM-G355M
Galaxy K Zoom C115
Galaxy Note 4_N910C
Galaxy Note GT N7000 Ginger Bread
Galaxy Note GT N7000 Ice Cream Sandwich
Galaxy Note GT N7000 Jelly Bean
Galaxy Note SGH -i717 AT&T Ice Cream Sandwich
Galaxy Note SGH -i717 AT&T Jelly Bean
Galaxy Note SGH -i717 BELL
Galaxy Note SGH -i717D
Galaxy Note SGH -i717R
Galaxy S5 SM-G900A
Galaxy S5 SM-G900A Rooted ROM
Galaxy S5 SM-G900F (UK)
Galaxy S5 SM-G900F (Germany)
Galaxy S5 SM-G900F (Malaysia)
Galaxy S5 SM-G900P Lollipop
Galaxy S5 SM-G900P Full Restore (Unrooted)
Galaxy S5 SM-G900P 5.0 Default
Galaxy S5 SM-G900P (Rooted)
Galaxy S5 SM-G900T Lollipop
Galaxy S5 SM-G900T 4.4.4 (Rooted)
Galaxy S5 SM-G900T Default
Galaxy S5 SM-G900V Lollipop
Galaxy S5 SM-G900V Rooted
Galaxy S5 SM-G900W8 Virgin Mobile
Galaxy S5 SM-G900W8 Telus
Galaxy S5 SM-G900W8 Mobilicity
Galaxy S5 SM-G900W8 Sasktel
Galaxy S5 SM-G900W8 Rogers

Request, Complain and Gratitude

Name

Email *

Message *